W32.Badtrans.B@mm Removal Tool

SUMMARY

What the tool does
The W32.Badtrans.B@mm Removal Tool does the following:

1. Terminates all the viral W32.Badtrans.B@mm processes.
2. Deletes any W32.Badtrans.B@mm executable files.

CAUTION: This tool will only remove W32.Badtrans.B@mm. It cannot be used to remove other variants of W32.Badtrans


Command-line switches available with this tool
/SILENT, /S - Enables silent mode.
/LOG=[PATH NAME] - Creates a log file where [PATH NAME] is the location in which to store the output of the tool.
/START - Forces the tool to start scanning immediately.



To obtain and run the tool

CAUTION: Once a computer has been attacked by W32.Badtrans.B@mm, it is possible that the system security has been compromised. For this reason, all the passwords used on an infected computer should be changed. This includes Remote Access and Dial-Up Networking passwords, remote shares passwords, and so on.

NOTE: You must have administrative rights to run this tool on Windows NT4.

1. Download the FixBadtr.exefile from:
   
   http://securityresponse.symantec.com/avcenter/FixBadtr.exe
   
2. Save the file to a convenient location, such as your download folder or the Windows desktop (or removable media that is known to be uninfected, if possible).
3. To check the authenticity of the digital signature, refer to the section The digital signature.
4. Close all running programs before running the tool.
5. If you are on a network or you have a full-time connection to the Internet, disconnect the computer from the network and the Internet.
6. If you are running Windows Me or XP, then disable System Restore. Please refer to the section System Restore option in Windows Me/XP for additional details.
   
   NOTE: If you are running Windows Me/XP, we strongly recommend that you do not skip this step.
   
7. Double-click the FixBadtr.exe file to start the removal tool.
8. Click Start to begin the process, and then allow the tool to run.
9. If necessary, download the appropriate Microsoft patch to patch vulnerable systems. This patch can be found at the following Microsoft site:
   
   http://www.microsoft.com/technet/security/bulletin/MS01-020.asp
   
10. Restart the computer.
    
    NOTE: The registry key value that was created by the worm will not be removed until the computer is rebooted.
    
11. Run the removal tool again to ensure that the system is clean.
12. Install the necessary Microsoft patch to patch the vulnerable system.
13. If you are running Windows Me or XP, then re-enable System Restore.
14. Run LiveUpdate to make sure that you are using the most current virus definitions.
    
    NOTE: The removal procedure might be unsuccessful if Windows Me/XP System Restore is not disabled as previously directed because Windows prevents System Restore from being modified by outside programs. Because of this, the removal tool might fail.

When the tool has finished running, you will see a message indicating whether the computer was infected by the W32.Badtrans.B@mm. In the case of a removal of the worm, the program displays the following results:

• The total number of the scanned files.
• The number of deleted files.
• The number of viral processes terminated.

The digital signature
FixBadtr.exe is digitally signed. Symantec recommends that you only use copies of FixBadtr.exe that have been downloaded directly from the Symantec Security Response download site. To check the authenticity of the digital signature, follow these steps:

1. Go to http://www.wmsoftware.com/free.htm
2. Download and save the chktrust.exe file to the same folder where you saved FixBadtr.exe (for example, C:Downloads).
3. Depending on your operating system, do one of the following:
   • Click Start, point to Programs, and click MS-DOS Prompt.
   • Click Start, point to Programs, click Accessories, and then click Command Prompt.
   • Change to the folder where FixBadtr.exe and Chktrust.exe are stored, and then type:
     
     chktrust -i FixBadtr.exe
     
     For example, if you saved the file to the C:Downloads folder, you would enter the following commands:
     
     cd
     cd downloads
     chktrust -i FixBadtr.exe
     
4. Press Enter after typing each command. If the digital signature is valid, you will see the following:
   
   Do you want to install and run "BadTrans Fix Tool" signed on 11/29/2001 10:53 AM and distributed by Symantec Corporation.
   
   NOTES:
   • The date and time that are displayed in this dialog box will be adjusted to your time zone if your computer is not set to the Pacific time zone.
   • If you are using Daylight Saving time, the time that is displayed will be exactly one hour earlier.
   • If this dialog box does not appear, there are two possible reasons:
     • The tool is not from Symantec. Unless you are sure that the tool is legitimate, and that you downloaded it from the legitimate Symantec Web site, you should not run it.
     • The tool is from Symantec, and is legitimate. However, your operating system was previously instructed to always trust content from Symantec. For information on this, and how to view the confirmation dialog again, read the document How to restore the Publisher Authenticity confirmation dialog box.
5. Click Yes to close the dialog box.
6. Type exit and then press Enter. This will close the MS-DOS session.

System Restore option in Windows Me/XP
Windows Me and Windows XP users should temporarily turn off System Restore. This feature, which is enabled by default, is used by Windows Me/XP to restore files on your computer in case they become damaged. When a computer is infected with a virus, worm, or Trojan, it is possible that the virus, worm, or Trojan could be backed up by System Restore. By default, Windows prevents System Restore from being modified by outside programs. As a result, there is the possibility that you could accidentally restore an infected file, or that on-line scanners would detect the threat in that location. For instructions on how to turn off System Restore, read your Windows documentation or one of the following articles:

• How to disable or enable Windows Me System Restore.
• How to disable or enable Windows XP System Restore.

For additional information, and an alternative to disabling System Restore, see the Microsoft Knowledge Base article Anti-Virus Tools Cannot Clean Infected Files in the _Restore Folder, Article ID: Q263455.


How to run the tool from a floppy disk

1. Insert the floppy disk that contains the Fixbadtr.exe file in the floppy disk drive.
2. Click Start and then click Run.
3. Type the following and then click OK:
   
   a:fixbadtr.exe
   
   NOTES:
   • There are no spaces in the command a:fixbadtr.exe
   • If you are using Windows Me, and the System Restore remains enabled, you will see a warning message. You can choose to run the removal tool with the System Restore option enabled or exit the removal tool.
     
4. Click Start to begin the process, and then allow the tool to run.
5. If you are using Windows Me, then reenable System Restore.